Garage Doors

Shenzhen Jiaxingyuan Science & Technology Co., Ltd

Do not do business with this company. They have a very low quality product. glass on door is cracking after 1 month. frosting is pealing off. company refuses to do anything about it.

photo 1

http://www.szjiaxingyuan.com

Plant adress: Jianshang Industrial Park, Jianshang Village, Minzhi Street, Baoan District, Shenzhen City, Guangdong Provice,China

Office adress: Floor 6 , The New Building, Jianshang Village, Mingzhi Street, Baoan District, Shenzhen City, Guangdong Provice,China
Overseas Sales dept: Manager Chen
Tel?0086-755-23058632
Fax?0086-755-29402361
Tel?0086-13823582315
Tel?Email:sale@szjiaxingyuan.com
Http?
www.szjiaxingyuan.com
Post Code?518109

Domestic Sales dept: Manager Chen
Tel?0086-755-23058632
Fax?0086-755-29402361
Tel?0086-13823582315
Email:sale@szjiaxingyuan.com
Http?
www.szjiaxingyuan.com
Post Code ?518109

Beada Frame 7″ LCD Display + Companion Board for TI Cortex-A8 AM3359 Beaglebone

Beada Frame 7″ LCD Display + Companion Board for TI Cortex-A8 AM3359 Beaglebone

Beada Frame: 7″ TFT LCD Display with Touch

+

Companion Board for TI Cortex-A8 Sitara AM3359 Beaglebone

Seller information

WARNING. i have purchased this screen and was ripped off by the China seller. DO NOT BUY THIS PRODUCT. The screen was defective and the seller refused to refund after i shipped the item back. I could not open a dispute with ebay because it was over the 45 days buyers protection. Buy from a reputable american company.

Outer Wheel House Does Not Fit!

Reproduction GTO Wheel wells do not fit convertibles. modifications made to outer wheel well. I only cut out the top portion saving the side lip because they fit.

IMG_1178[1]

test fit of wheel well. the top needs to be flat. i plan to fill the top with a flat piece of sheet metal.IMG_1179[1]

Swiss Cheese Rust

The passenger outer rocker had a lot of rust holes. Almost like swiss cheese. The panel it self was in good structural shape. it would have been a lot of work to cut and weld so many smaller patches. I decided to fill these holes with the mig welder. On the right side of the image you can see i already filled some holes.

After a little wire wheeling.

As a backing i used the a copper ‘welding helper spatula spoon’ thingumabob. Steel weld does not stick to the copper so the spoon comes right off. After a little grinder the final result was to my satisfaction. i held the spoon on the outside of the rocker and welded from the inside. i only need to grind down the outside since the inside will no longer be visible once the floor and inside rockers go back in.

holes filled and finished off with sandpaper flap disk on grinder.

the two holes on the left were too big. had to fill with a metal patch.

End result. almost perfect but once some primer goes on and a little filler to cover. the work will not be noticeable.

i am not sure how ‘correct’ this type of repair is as i have not seen it done or discussed in the forums. But i like it!

Inside Rocker

Getting the rust out of the inside of the rockers would have been impossible without sandblasting. With the new compressor sandblasting was a lot smoother. No need to wait for the compressor to catch up. Only downside is that sand gets EVERYWHERE. Between the sand and the paint fumes the garage wax toxic. I had my respirator on until the last minute before running out the door.

After blasting i spray painted with eastwoods rust encapsulator.